1 / 4 www.asb.co.kr february 2011 p lerow tm ALN1922 internally match ed lna module the plerow tm aln - series is the compactly designed surface - mount module for the use of the lna with or without the following gain blocks in the infrastructure equipment of the mobile wireless (cdma, gsm, pcs, phs, wcdma, dmb, wlan, w ibro, wimax), gps, satellite commun i- cation terminals , catv and so on. it has an exceptional performance of low noise figure, high gain, high oip3, and low bias current. the stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. the surface - mount module package including the completed matching circuit and other components necessary just in case allows very simple and convenient implementatio n onto the system board in mass production level. parameter unit specifications min typ max frequency range mhz 1850 1995 gain db 29.0 30.0 gain flatness db 0.4 0.5 noise figure db 0.65 0.7 output ip3 dbm 37.5 39 s11/s22 db - 18/ - 9 output p1db dbm 20 21 swit ching time (3) m sec - supply current ma 170 200 supply voltage v 5 impedance w 50 max. rf input power dbm c.w 29~31 (before fail) package type & size mm surface mount type, 13wx13lx3.8h operating temperature is - 40 c to +85 c. 1) oip3 is measured with two tones at an output power of 4 dbm/tone separated by 1 mhz. 2) s11/s22 (max) is the worst value within the frequency band. 3) switching time means the time that takes for output power to get stabilized to its final level after switching dc voltage from 0 v to v s . pin number function 3 rf in 8 rf out 10 v s other s ground ou t line drawi ng (unit: mm) feature s s 21 = 30.4 db@1850 mhz = 29.6 db@1995 mhz nf of 0.65 db over fr e quency unconditionally stable single 5 v supply high oip3@low current note: 1. the number and size of ground via holes in a circuit board is critical for thermal rf grounding consider a tions. 2. we recommend that the ground via holes be placed on the bottom of all ground pins for better rf and thermal performance, as shown in the dra w ing at the left side. description ALN1922 asb inc. (top view) (bottom view) solder stencil area ? 0.4 plated thru holes to ground plane plerow (side view) (recommended footprint) website: www.asb.co.kr e - mail: sales@asb.co.kr tel: (82) 42 - 528 - 722 3 f ax : (82) 42 - 528 - 7222 more inform a tion 2 - stage single type specifications (in pr o duction) typ.@t = 25 c, v s = 5 v, freq. = 1922.5 mhz, z o.sys = 50 ohms
2 / 4 www.asb.co.kr february 2011 p lerow tm ALN1922 internally match ed lna module s - param e ters noise figure oip3 p1db 1850~1995 mhz +5 v typical performance (measured) s - parameters & k fa c tor
3 / 4 www.asb.co.kr february 2011 p lerow tm ALN1922 internally match ed lna module 1. s - parameter 2. oip3, p1db & nf note: tested at room temperature. 1. s - parameter 2. oip3, p1db & nf note: tested at v s = 5 v . 1850 mhz 1922.5 mhz 1995 mhz s21 (db) s11 (db) s22 (db) s21 (db) g/f (db) s11 (db) s22 (db) s21 (db) s11 (db) s22 (db) 4.50 v 30.21 - 21.04 - 12.28 29.82 0.71 - 18.85 - 12.54 29.50 - 18.76 - 11.51 4.75 v 30.27 - 21.68 - 12.34 29.87 0.72 - 19.38 - 12.57 29.55 - 19.37 - 11.55 5.00 v 30.37 - 22.55 - 12.57 30.02 0.73 - 20.11 - 12.70 29.64 - 20.26 - 11.68 5.25 v 3 0.34 - 22.90 - 12.38 29.94 0.73 - 20.41 - 12.52 29.61 - 20.55 - 11.51 5.50 v 30.33 - 23.57 - 12.29 29.92 0.73 - 20.90 - 12.46 29.60 - 21.08 - 11.45 1850 mhz 1922.5 mhz 1995 mhz oip3 (dbm) p1db (dbm) nf (db) oip3 (dbm) p1db (dbm) nf (db) oip3 (dbm) p1db (dbm) nf (db) 4.50 v 38.62 19.18 0.564 38.75 18.90 0.565 39.20 18.55 0.621 4.75 v 39.10 19.98 0.607 39.24 19.15 0.591 39.45 19.80 0.634 5.00 v 39.50 21.35 0.610 39.78 21.22 0.619 39.85 21.05 0.649 5.25 v 38.44 21.67 0.647 38.84 21.50 0.659 38.98 22.10 0.691 5.50 v 38.21 22.70 0.697 38.45 21.96 0.679 38.76 22.42 0.720 1850 mhz 1922.5 mhz 1995 mhz s21 (db) s11 (db) s22 (db) s21 (db) g/f (db) s11 (db) s22 (db) s21 (db) s11 (db) s22 (db) - 45 c 30.58 - 24.18 - 14.91 30.28 0.72 - 26.24 - 13.39 29.86 - 24.46 - 12.66 - 10 c 30.54 - 22.89 - 13.68 30.20 0.75 - 23.88 - 12.51 29.79 - 22.12 - 12.14 25 c 30.38 - 21.54 - 12.89 30.01 0.71 - 21.66 - 11.86 29.67 - 20.17 - 11.65 60 c 30.13 - 20.65 - 11.94 29.78 0.75 - 20.52 - 11.00 29.38 - 19.15 - 11.03 85 c 29.97 - 20.00 - 11.17 29.63 0.74 - 19.74 - 10.32 29.23 - 18.35 - 10.47 1850 mhz 1922.5 mhz 1995 mhz oip3 (dbm) p1db (dbm) nf (db) oip3 (dbm) p1db (dbm) nf (db) oip3 (dbm) p1db (dbm) nf (db) - 45 c 39. 25 21.19 0.375 39.20 20.84 0.381 39.48 21.29 0.408 - 10 c 39.40 21.25 0.468 39.80 20.94 0.475 39.65 21.40 0.488 25 c 39.65 21.48 0.623 39.91 21.13 0.629 40.02 21.43 0.645 60 c 39.35 20.85 0.801 39.64 20.62 0.813 39.73 20.95 0.823 85 c 39.04 20.68 0. 976 39.25 20.45 0.984 39.40 20.75 0.991 rf performance with operating temperature rf performance with voltage change
4 / 4 www.asb.co.kr february 2011 p lerow tm ALN1922 internally match ed lna module 1) the tantal or mlc (multi layer ceramic) capacitor is optional and for bypassing the ac noise introduced from the dc supply. the capacitance value may be de termined by customer s dc supply status . the c a- pacitor should be placed as close as possible to v s pin and be connected directly to the ground plane for the best electrical performance . 2) dc blocking capacitors are always necessarily placed at the input and output port for allowing only the rf signal to pass and blocking the dc component in the signal. the dc blocking capacitors are i n clu d- ed inside the aln module. therefore, c1 & c2 capacitors may not be necessary, but can be added just in case that the custo mer wants. the value of c1 & c2 is determined by considering the application fr e- quency. application circuit recommended soldering reflow process + - aln out in c1 c2 v s tantal or mlc (multi layer c e ramic) c a pacitor 20~40 sec 260 c 200 c 150 c 60~180 sec ramp - up (3 c/sec) ramp - down (6 c/sec) in out vs size 25x25mm (for aln series C 13x13mm) evaluation board layout
|
